Shown in green. Photos: Axial. SCX30 Toyota Tacoma TRD Pro Axial · Micro rock crawler
Last seen 2026-11-06 Item prices. Delivery and taxes are set by each store.
Setup shown Green · AXI-3289T1
Features a rock-crawler focused build with a wider stance and fender delete.
Version details & sources Equipped with BFGoodrich Krawler tires and KMC Torx wheels.
Includes a purpose-built tube-style bumper aesthetic.
Just over 2 payment cards
6.9 in / 17.5 cm long 1/30 scale
First drive Tools Upgrades Fix a problem Care
What it’s like to drive.
Your first drive. Included Car (assembled) Included Controller Included Battery Included Charger Included Controller batteries · 4 × AA Full box contents 1 × SCX30 chassis, drivetrain, and suspension 1 × Spektrum SLT2 2.4GHz radio transmitter 1 × Spektrum SCX30 SLT Brushed 2-in-1 ESC/Receiver (installed) 1 × Axial 88T 030-sized brushed motor (installed) 1 × Spektrum 7.4V 160mAh 2S 30C LiPo battery 1 × USB 2S Charger: 0.5A JST-XH 3P 4 × AA transmitter batteries 1 × Instruction manual Package information for AXI-3289T1 in green.
No extra RC gear needed.
Use a 5V, 1A USB power source to charge the battery.
Never leave charging batteries unattended or charge overnight.
First-drive instructions Disconnect the battery immediately if it becomes hot or begins to puff. Never remove transmitter batteries while the vehicle is powered ON. Charge the vehicle battery Confirm the output voltage of your USB power supply conforms to the charger specifications before connecting. Plug the charger into a USB port on a computer or a USB power supply. Connect the battery balance connector to the charger's charge port. Observe the LEDs: solid red and blinking green indicate charging has started. Wait for the LED to turn solid green, indicating the charge is complete (approx. 20-40 minutes for a 160mAh battery). Immediately remove the battery from the charger once charging is complete. Do not leave the battery connected. Manufacturer instructions · page 4 Install the transmitter batteries Press the battery compartment latch and rotate the battery cover to open. Install 4 AA alkaline batteries, verifying correct polarity. Close the battery cover until it latches. Manufacturer instructions · page 6 Test the controls With wheels off the ground, test throttle and steering to ensure proper direction. Start driving slowly on the ground. If the vehicle does not go straight, adjust the steering trim dial on the transmitter. Manufacturer instructions · page 8 After driving & battery storage What would you like to change? More time driving, a different feel, or a truck that looks like yours. You don’t have to change everything.
Drive for longer Spare batteries & charging Spektrum
Spektrum 7.4V 160mAh 2S 30C LiPo Battery Replacement 2S LiPo battery with PH2.0 connector for extended runtime.
Designed specifically for SCX30 battery compartment.
Contents, fit & sources Spektrum 7.4V 160mAh 2S 30C LiPo Battery
Details checked 2026-10-20 .
Find more grip Tires, wheels & inserts Mofo RC
Mofo RC Stock Wheel Weights Friction-fit wheel weights to increase traction and stability.
Press into stock wheels; align cutouts with wheel vents. Tighten wheel nut then back off 1/4-1/2 turn for clearance.
Contents, fit & sources Mofo RC Stock Wheel Weights
Details checked 2026-10-20 .
INJORA
INJORA 0.7" King Trekker Tires Soft S5 compound tires with aggressive tread for improved traction on rocks and technical terrain.
Designed and tested exclusively for use with INJORA wheels; compatibility with other wheels is not guaranteed.
Contents, fit & sources INJORA 0.7" King Trekker Tires
Details checked 2026-10-20 .
Axial
Axial Tires & Foam (5), Geolandar XMT A set of five Yokohama Geolandar XMT tires with open cell foam inserts for improved traction.
Compatible with SCX30 platform wheels.
Contents, fit & sources Axial Tires & Foam (5), Geolandar XMT
Details checked 2026-10-19 .
Change how it drives Brushed & brushless power Mofo RC · Brushed
NeoBeast 30 Brushed Motor Replacement brushed motor for SCX30 chassis featuring neodymium magnets for increased torque and low-speed control.
Controller Keep your controller
Do not remove the wire retaining rubber band
Compatible with stock ESC
Contents, fit & sources NeoBeast 30 Brushed Motor · NeoBeast 30
The stock Spektrum SLT2 transmitter and 2-in-1 ESC/receiver are compatible with this motor.
Setup requirements Bolt motor into stock motor mount Connect motor wires to ESC In this package NeoBeast 30 Brushed Motor Mod.3 11t Pinion (pre-installed) Wire retaining rubber band Use what you have Stock Spektrum SCX30 SLT 2-in-1 ESC/Receiver Stock Spektrum SLT2 transmitter Direct fit for Axial SCX30 chassis; includes pre-installed Mod.3 11t pinion.
Details checked 2026-10-20 .
Furitek · Brushless
NanoModo 2026 Stock TX Plug & Play System Integrated brushless upgrade for Axial SCX30, replacing stock brushed ESC/receiver and motor with brushless components.
Controller Keep your controller
Perform one-time binding of the Furitek Micro SLT2 receiver to the stock transmitter
Before ordering Your battery uses PH 2.0. Match your battery plug to the ESC’s battery socket or selected adapter.
Contents, fit & sources NanoModo 2026 Stock TX Plug & Play System · NanoModo 2026
ESC features integrated wireless tuning via Furicar App
Designed for use with the stock Spektrum SLT2 transmitter; requires a one-time binding procedure.
In this package NanoPython Brushless FOC ESC NanoKomodo Brushless Motor Furitek Micro SLT2 Receiver Servo Adapter Cable 11T Pinion Gear Use what you have Spektrum SLT2 transmitter Designed for the SCX30 chassis layout; check battery connector compatibility with the new ESC input.
Details checked 2026-10-21 .
INJORA · Brushless
MBL32-NANO Brushless System Upgrade to a sensorless brushless outrunner motor and ESC system for 1/30 scale crawlers.
Controller Different controller needed
Buy separately Handheld controller Receiver · a channel-2 output port 3S batteries may damage the 1621 motor
Use 2S LiPo battery only
Do not flash or modify firmware
Before ordering Your battery uses PH 2.0. Match your battery plug to the ESC’s battery socket or selected adapter.
Contents, fit & sources MBL32-NANO Brushless ESC & 1621 Green Viper Motor 4300KV · MBL32-NANO-INM24
USB programmer card is not included
Use a different handheld controller and a separate receiver inside the rig.
In this package MBL32-NANO Brushless ESC 1621 Brushless Motor Instruction Manual The 1621 motor uses PH2.0 3-pin connectors. Verify the stock battery PH 2.0 power plug compatibility with the new ESC input.
Details checked 2026-10-20 .
More options (1) Mofo RC · Brushless
NanoBeast Brushless Combo Upgrade to a brushless motor and ESC system for the SCX30 platform.
Buy separately Receiver · channel-2 output throttle port Requires replacing the stock 2-in-1 ESC/receiver
ESC includes default settings which may require adjustment
Motor shaft accepts press-fit pinions only
Before ordering Your battery uses PH 2.0. Match your battery plug to the ESC’s battery socket or selected adapter.
Contents, fit & sources NanoBeast 3200Kv Brushless Motor & Reaper ESC Combo · NanoBeast-Reaper-Combo
The stock 2-in-1 ESC/receiver combo must be replaced because it lacks a channel 2 throttle port.
Setup requirements Remove stock 2-in-1 ESC/receiver Install Reaper ESC Install NanoBeast motor Connect motor to ESC Connect ESC to new receiver In this package NanoBeast 3200Kv brushless motor Pre-installed Mod.3 11t pinion Reaper 30A ESC JST/PH adapters Use what you have Chassis Drivetrain Suspension Motor dimensions are 14.6mm diameter by 20.5mm length. Verify the new ESC and receiver fit within the SCX30 chassis space.
Details checked 2026-10-20 .
More ways to make it yours Steer with more control Servos & steering Furitek
Micro SLT2 Receiver Enables stock transmitter use with Furitek ESCs.
Controller Keep your controller
Compatible with Furitek ESCs only.
Perform a one-time bind to the stock transmitter.
Contents, fit & sources Furitek Micro SLT2 Receiver · Micro SLT2 Receiver
Retains stock Spektrum SLT2 transmitter.
In this package Furitek Micro SLT2 Receiver Use what you have Stock Spektrum SLT2 transmitter Compatible only with Furitek ESCs (NanoPython, MicroPython, Nano UNITY). Not compatible with other ESC brands.
Read the supplier’s details Details checked 2026-10-21 .
INJORA
INJORA High Torque N30 PRO NANO Servo A high-torque servo with metal gears and an aluminum case for improved steering response and durability.
Available in JR or ZH1.5 connector versions to match your receiver. Use a small driver and light pressure during installation.
Also needed Correct-size driver for small hardware Contents, fit & sources INJORA High Torque N30 PRO NANO Servo
Not waterproof.
Details checked 2026-10-20 .
Tune the way it handles Weight, suspension & links Mofo RC
Mofo RC 0.7" Weighted Wheels Weighted wheels allow for front-to-rear weight bias adjustment and use of larger 0.7" tires.
Wheels are slightly oversized for a friction fit; gluing is optional. Brass weights will naturally tarnish.
Contents, fit & sources Mofo RC 0.7" Weighted Wheels
Details checked 2026-10-19 .
INJORA
INJORA Black Brass Steering Links Brass steering links add front-end weight to improve climbing stability and control.
Direct replacement for stock links. Includes a Torx screwdriver for installation.
Contents, fit & sources INJORA Black Brass Steering Links
Details checked 2026-10-20 .
Mofo RC
Mofo RC Brass Steering Knuckle Brass steering knuckles add 2.5g of weight over stock per side for improved handling.
Direct replacement for stock SCX30 knuckles; includes 4 bearings.
Contents, fit & sources Mofo RC Brass Steering Knuckle
Adds unsprung weight to the front axle.
Details checked 2026-10-19 .
More options (2) INJORA
INJORA 26mm Aluminum Oil Shocks Aluminum oil-filled shocks provide consistent damping and adjustable preload for the SCX30.
Shock oil is not included. Filling may require a specialized tool due to the compact size.
Contents, fit & sources INJORA 26mm Aluminum Oil Shocks
Details checked 2026-10-20 .
INJORA
INJORA 0.7" D19 Ripple Black Solid Brass Wheels CNC-machined brass wheels add low-positioned weight to improve crawling stability.
Designed for 1/30 Axial SCX30; compatibility with non-INJORA tires may vary due to bead design. Includes Torx screwdriver.
Also needed INJORA 0.7" tires recommended for best fit Contents, fit & sources INJORA 0.7" D19 Ripple Black Solid Brass Wheels
Adds significant unsprung weight compared to stock wheels.
Details checked 2026-10-20 .
Replace a worn part Gears, shafts & replacements INJORA
INJORA Stainless Steel Drive Shafts Reinforced stainless steel drive shafts with an in-phase design for increased strength.
Use a small driver and light pressure during installation. Stop if you feel resistance before the screw is seated.
Also needed Correct-size driver for small hardware Contents, fit & sources INJORA Stainless Steel Drive Shafts
Details checked 2026-10-20 .
Axial
Axial 88T 030-Size Brushed Motor A direct-fit replacement 88T brushed motor with pre-installed wire, PH2.0 connector, and 11T brass pinion.
Designed specifically for the SCX30 platform. Includes a press-fit 11T 0.3 mod brass pinion.
Contents, fit & sources Axial 88T 030-Size Brushed Motor
Details checked 2026-10-19 .
Make it look like yours Bodies & appearance Axial
Axial Bumpers, Fenders: SCX30 Toyota Tacoma Replacement fender and bumper set including Overland and Crawler styles.
Compatible with SCX30 Toyota Tacoma body.
Contents, fit & sources Axial Bumpers, Fenders: SCX30 Toyota Tacoma
Details checked 2026-10-21 .
Axial
SCX30 Toyota Tacoma Body Set Replacement body set including decal sheet for the Toyota Tacoma.
Designed specifically for the SCX30 Toyota Tacoma.
Contents, fit & sources SCX30 Toyota Tacoma Body Set
Details checked 2026-10-20 .
Product options are described by their makers. Choose the matching version at the store.
Parts you can 3D print. Files made by hobbyists. Print them yourself or ask a printing service.
SCX30 Flatbed (New 4-door Tacoma) Design by Baloo’s RC · Digital files
SCX30 Flatbed (New 4-door Tacoma) Replaces stock bed for improved departure angle and custom appearance.
Fits Designed for Axial SCX30 Tacoma; requires manual hole drilling or adhesive for mounting.
Print material PETG-CF or PETG Basic recommended. Custom fitting Drill 1/8 inch holes in flatbed to align with cab Notch rear mounting tab with scissors if retaining stock taillight Printing, fitting & sources Also needed: Double-sided tape or adhesive · Optional M2 hardware for screw mounting
Standard Digital File License
Use the creator’s instructions and file version.
Get back to driving. Pick what’s happening. Try the checks before buying a replacement.
The truck won’t move Verify transmitter battery installation If the transmitter batteries are not installed properly, the vehicle may not move.
Next step Ensure the transmitter batteries are properly installed per the manual.
Install a freshly charged vehicle battery If the vehicle battery is weak or empty, the vehicle will not move.
Next step Charge the battery using the included USB charger.
Allow the ESC to cool If the Electronic Speed Controller (ESC) overheats, the LED flashes rapidly and the motor powers off.
Next step Allow the ESC to cool down completely until the LED returns to normal.
Manufacturer checks & sources The controls stop responding Check transmitter antenna orientation If the front of the transmitter is covered, the RF signal may be blocked, resulting in loss of control.
Next step Hold the transmitter oriented as close to vertical as possible and do not cover the front.
Replace transmitter and vehicle batteries If the transmitter or vehicle batteries are weak, control may be lost.
Next step Install a freshly charged vehicle battery and new transmitter batteries.
Manufacturer checks & sources The battery isn’t charging Observe charger LED status If the charger LED shows a red blinking and green solid light, the input voltage is too high.
Next step Confirm the USB power supply output is 5V.
If the charger LED shows a red blinking light, there is a battery error.
Next step Contact Horizon Hobby for assistance.
If the charger LED shows red and green blinking, there is a charger error.
Next step Contact Horizon Hobby for assistance.
Manufacturer checks & sources Controller settings & pairing Use the equipment named in each procedure. Check the model number and revision on your controller before changing settings.
Steering Direction Reversal Spektrum SLT2 2.4GHz radio transmitter (SPMRSLT270)
Before you start Ensure the transmitter has fresh batteries installed. Keep the wheels of the model off the ground when checking the operation of the radio equipment. Set the transmitter servo reversing switch to the correct position.
Finish up Verify the front wheels turn in the proper direction with steering input.
Check all receiver and battery connections, or contact Horizon Hobby support.
Manufacturer instructions & sources [Page 1] · Page 13 Adjust Steering Trim Spektrum SLT2 2.4GHz radio transmitter
Before you start Ensure the vehicle wheels are off the ground when checking the operation of the radio equipment. Always turn on your transmitter before you turn on the receiver in the car. Start driving slowly to check for proper direction of controls. Adjust the steering trim dial on the transmitter until the vehicle holds a straight line with no steering input.
Finish up Have FUN driving your vehicle!
If the vehicle veers left, correct with right trim. If the vehicle veers right, correct with left trim.
Manufacturer instructions & sources [Page 1] · Page 6 Limit Throttle Output Spektrum SLT2 2-CH 2.4GHz transmitter (SPMRSLT270)
Before you start Power on the transmitter. Power on the vehicle. Locate the THROTTLE LIMIT switch on the transmitter.
Finish up Select 50% or 75% for less experienced drivers or when driving the vehicle in a small area.
Ensure the transmitter is powered on and the vehicle is bound to the transmitter.
Manufacturer instructions & sources [Page 1] · Page 5 Pairing the Receiver Spektrum SLT2 2.4GHz radio transmitter and Spektrum SCX30 SLT Brushed 2-in-1 ESC/Receiver (AXI-3289)
Before you start Ensure the servos and motor are connected to the proper ports on the receiver. Ensure the transmitter has fresh batteries installed. Do not attempt to bind if other compatible transmitters are in bind mode within 400 feet. Connect the battery to the receiver.
Press and hold the power button for 3 seconds.
You should see The red light flashes rapidly.
Release the button.
Power ON the transmitter.
Wait for the 2-in-1 and transmitter LEDs to glow solid.
You should see Binding is complete; the receiver LED will glow solid when both are powered on.
Finish up The receiver LED will glow solid when both the transmitter and receiver are powered on.
If the receiver LED flashes rapidly or is not illuminated, the transmitter and receiver are not bound. Power off both the transmitter and receiver and repeat the binding procedure.
Manufacturer instructions & sources [Page 1] · Page 9 Steering Servo Travel Adjustment SPMRSLT270 · DSC-compatible controller revision
Before you start Ensure vehicle is powered off. Ensure transmitter is powered off. Begin with transmitter binding process to receiver complete.
Ensure vehicle wheels point straight ahead. Transmitter wheel is in the neutral (center) position.
"Throttle limit (THLIM)" (“5”) at 100% position.
Steering Rate dial (“7”) on the Transmitter is turned fully clockwise.
Power on vehicle.
Hold brake (forward position of Throttle/Brake “2”) and full right turn on the Steering Wheel (“1”) while powering on transmitter.
Turn Steering Wheel to full left to adjust travel for that direction. Turn Steering Rate dial (“7”) to increase or decrease travel.
Turn Steering Wheel to full right and repeat process to set steering travel to the right.
Return Transmitter wheel to center.
Slide "Throttle limit (THLIM)" (“5”) to 75% position to exit steering-travel setup
Power off vehicle.
Power off Transmitter.
Return “Throttle limit (THLIM)” (“5”) and Steering Rate (“7”) dial to desired position for driving.
Finish up Settings are saved and the transmitter is ready for normal driving.
Contact Horizon Product Support for further assistance.
Manufacturer instructions & sources [Page 1] · Page 3 Factory Reset for Spektrum SLT270 SPMRSLT270 · DSC-compatible controller revision
Before you start Ensure the transmitter is powered off. Hold full left and full brake while powering the transmitter on.
You should see The LED will flash four times.
Release the steering and throttle controls.
You should see The LED will flash once to indicate factory reset is complete.
Power the transmitter off.
Finish up The transmitter settings are reset to factory defaults.
Contact Horizon Product Support for further assistance.
Manufacturer instructions & sources [Page 1] · Page 3 Set Running Mode Spektrum SCX30 SLT Brushed 2-in-1 ESC/Receiver (SPMXSE3225RX)
Before you start Power the vehicle ON to begin programming the settings. Press and hold the power button for three seconds.
You should see The LED slowly flashes once.
Release the power button.
You should see The number of flashes indicates the Running Mode Setting.
Press the power button to move to the next option.
Press and hold the power button for three seconds to save the selection and power OFF.
Finish up The selection is saved and the vehicle powers OFF.
Contact Horizon Hobby support for further assistance.
Manufacturer instructions & sources [Page 1] · Page 9 Replacement parts Use the part number in your version’s diagram.
Parts at Axial Open the parts diagram
Keep it running. After your drive Press and hold for 1 second, then release to power off vehicle. Press and hold for 1 second, then release to power off the transmitter. Remove the vehicle battery and charge if necessary. Gently unplug the battery plug by holding the wire close to the plug and carefully pulling straight up. Never leave the battery connected to the vehicle during storage.
Manufacturer’s after-drive instructions · page 9 Ownership sources INJORA 0.7" 35*14mm King Trekker Tires for 1/30 SCX30 (T7014) (4) 2050 PH Screwdriver for Phillips screws for electronic applications | Wera Skip to product information Axial Body Set: SCX30 Toyota Tacoma | Axial Adventure INJORA Drivers for 1/30 Axial SCX30, 3.0mm Nut, 2.0mm Phillips, T3 Torx, 0.05" Hex Skip to product information INJORA 26mm Aluminum Oil Shocks for 1/30 Axial SCX30 INJORA Black Brass Steering Links for 1/30 Axial SCX30 Skip to product information Mofo RC | NeoBeast 30 Brushed Motor w/ Mod.3 11t Pinion (Direct Fit fo
– Mofo Rc Spektrum 7.4V 160mAh 2S 30C LiPo Battery: SCX30 PH2.0 | Spektrum Axial Bumpers, Fenders: SCX30 Toyota Tacoma | Axial Adventure INJORA MBL32-NANO Brushless ESC & 1621 Green Viper Motor 4300KV for 1/ Mofo RC | Stock Wheel Weights (For Axial® SCX30™) - Made In Texas (Sol
– Mofo Rc Axial 88T 030-Size Brushed Motor: SCX30 | Axial Adventure INJORA High Torque N30 PRO NANO Servo with Servo Saver for 1/30 SCX30 Axial 1/30 SCX30 Toyota Tacoma TRD Pro Extreme Off-Road 4X4 RTR Brushed Rock Crawler (Battery & Charger Included), Green | Axial Adventure Axial Tires & Foam (5), Geolandar XMT: SCX30 | Axial Adventure INJORA Stainless Steel Drive Shafts for 1/30 Axial SCX30 Axial Wrench, Wheel Nut, Serrated, Steel: SCX30 | Axial Adventure INJORA 0.7" D19 Ripple Black Solid Brass Wheels for 1/30 SCX30 (W7005) [Page 1] Getting Started with RC Cars? Read Our Ultimate Beginners Guide! Furitek Micro SLT2 Receiver for Axial SCX30 Stock SLT2 Transmitter (Co SCX30 Flatbed (New 4-door Tacoma) - Free 3D Print Model - MakerWorld [Page 1] Best RC Motor Type | Horizon Hobby RC Basher Vehicle Type | Horizon Hobby | Spektrum Ready-To-Run RC Cars | Horizon Hobby Furitek NanoModo 2026 Stock TX Plug & Play Control System (ESC + Brush [Page 1] [Page 1]
Details, when you need them. Exact dimensions & scale 17.5 × 7.2 × 6.8 cm · length × width × height
Scale 1/30. Scale does not establish the actual footprint.
Vehicle · 17.5 cm 2 payment cards · ISO/IEC 7810 ID‑1 · 17.12 cm long. Length comparison only; not actual screen size. Battery & charging requirements
Battery Included
Charger Included
Connector Type JST PH2.0 2P
LiPo Compatibility 2S
Max Battery Dimensions 1.57" x 0.35" x 0.59" (40mm x 9mm x 15mm) Charging instructions & box contents Technical specifications
Approximate Assembly Time No Assembly Required
Brakes Programmable
Bushing Material Metal
Chassis Composite Chassis
Completion Level Ready-To-Run
Differential Gear
Drive Type Forward/Reverse
Drivetrain 4WD
Final Drive Ratio 131.58
Gear Pitch Mod-0.3
Internal Gear Ratio 16.36
Make Toyota
Motor Size 030-sized
Motor Type Brushed
Pinion 11T
Power Type Electric
Product Weight With 160mah battery: 0.33 lbs. / 0.15 kg (150.3g)
Radio Included
Receiver Included
Speed Control Included
Tire Type BFG Krawler tires
Vehicle Size Micro
Vehicle Type Rock Crawler
Wheel Type KMC Torx wheels Where this information comes from Manufacturer descriptions are not our own driving tests. Package facts, store prices and ownership guidance have separate check dates.
Manufacturer facts checked 2026-10-17 .
Manufacturer RTR designation Manufacturer · Checked 2026-10-17
Controller batteries in the box Manufacturer · Checked 2026-10-17
Other first-drive equipment Manufacturer · Checked 2026-10-17
Controller battery requirement Manufacturer · Checked 2026-10-17
New to RC? Start here. A few useful things to know. No experience needed.
What makes hobby-grade RC different from a toy RC car? Hobby-grade vehicles are designed to be repaired by replacing individual parts when they break, whereas toy-grade products often lack available replacement parts. Hobby-grade models also feature proportional controls, meaning small movements on the handheld controller create small, precise movements on the vehicle.
Compare RC cars & trucks Sources What do the parts inside an electric RC car actually do?
Handheld controller (transmitter) The device held by the driver that sends steering and throttle signals to the vehicle.
Receiver The unit inside the vehicle that receives signals from the transmitter and relays them to the steering servo and speed controller.
Speed controller (ESC) An electronic accelerator that varies electrical power from the battery to the motor to control speed.
Steering servo The muscle of the steering system that uses a motor and gears to push and pull the wheels to direct the vehicle.
Motor The component that converts electrical energy into mechanical motion to drive the wheels.
Battery The onboard power source that provides the electricity needed to run the vehicle's electronics and motor.
Chassis The structural platform or frame that all other parts are bolted to. See this rig’s details Sources What is a receiver/ESC combo, and does this truck have one? This truck includes a 2-in-1 unit that combines the receiver and speed controller into a single component mounted inside the vehicle. The Spektrum SLT2 handheld controller is a separate device used to send signals to this internal unit. If you decide to upgrade your electronics later, you should check that your new radio system and motor are compatible with your chosen components.
Inside this version Spektrum SLT2 2.4GHz radio transmitter Spektrum SCX30 SLT Brushed 2-in-1 ESC/Receiver (installed) See what this rig needs Sources Does ready-to-run include everything? Ready-to-Run (RTR) means the vehicle is pre-built and bound to the included radio system. However, you should always check the product detail page for any additional components that may be required, such as specific batteries or chargers.
See what this rig needs Sources What does RC scale tell me? Scale indicates the size of the model relative to a full-size vehicle. A 1/30 scale model is roughly 1/30 the size of its real-life counterpart. Actual dimensions still vary between different models.
See this rig’s details Sources Where can I drive a truck this small? This 1/30 scale, 17.5 cm (6.9 inch) long truck is designed for navigating desktops, cluttered living rooms, and outdoor rock or dirt trails. The manufacturer does not establish performance for driving in grass.
Compare RC cars & trucks Sources More beginner questions What kind of RC driving would I enjoy? This vehicle is a rock crawler, which is designed to climb over and through rough terrain that stops other vehicles. Other types include monster trucks for versatile bashing, short course trucks for racing, and on-road cars for smooth pavement.
Compare driving styles Sources Can I make the controls gentler while learning? Yes, the transmitter features a throttle limit switch. You can select 50% or 75% output to make the vehicle easier to control for less experienced drivers or when operating in a small area.
Get help with this rig Sources What happens if I break something? Hobby-grade vehicles are designed for repair. You can consult the exploded views in your manual to identify specific parts and order replacements through authorized retailers or the manufacturer's support site.
Get help with this rig Sources Do I need brushless or upgrades straight away? Upgrades are a personal choice, not a requirement. Brushed motors are easy to maintain and affordable, while brushless motors offer more power and longevity if you choose to upgrade later.
Explore the options Sources How much battery care do I need to learn? You must never leave charging batteries unattended, never charge overnight, and always inspect the battery before charging. If the battery becomes hot or swells during charging, disconnect it immediately and stop the process.
See the care steps Sources How do I find the right replacement part? You can identify the correct replacement parts by consulting the exploded views section in your instruction manual. For the most current information and support, you can also visit the product page on horizonhobby.com and select the Support tab.
See this rig’s details Sources 